|
|
 |
|
 |
| | | INDOOR |
|
 THESE PRODUCTS ARE ONLY AVAILABLE IN CANADA
Wall Mounted Systems
|
|
This new adjustable three-point stationary wall mount incorporates a direct-goal-attachment for extended backboard life and telescoping braces for precision installation. The lower support is contructed of 3 ½" x 11 gauge mechanical tubing, telescoped inside of 4" x 10 gauge tubing. It tranfers the load of heavy play directly through the backboard to the wall structure.
This new adjustable three-point stationary wall mount incorporates a direct to goal attachment for extended backboard life and telescoping braces for precision installation. The lower support is contructed of 3 ½" x 11 gauge mechanical tubing telescoped inside of 4" x 10 gauge tubing. This tranfers the load of heavy play directly through the backboard to the wall structure.
|
|
|
This traditional four-point wall mounted backstop is designed for strength and simple installation. Backstop is constructed with 1 7/8" O.D. heavy-wall tubing, malleable castings, heavy gauge stampings and weldments. Backstop utilizes tension straps and threaded rods to increase stability. On extensions greater than 18", top braces are bent for added rigidity. Unit is attached with 2" x 6" wood stringers. Extendable up to 12'.
|
|
|
This backstop features pivoting 1 7/8" horizontal extension tubes that allow the unit to fold up and out of the way of other court activities. Backstop utilized with 1/4" x 1" tension straps and 1 7/8" braces. 4/0 upper safety chains provided for additional support. Extensions from 4 to 12 feet. Requires manual winch.
|
 |
|
This backstop folds to the side and flat against the wall. Backstop rigidly locks into playing position with telescoping slide pipes featuring automatic spring locks. Constructed with 1 7/8" x 12 gauge mechanical tubing that is utilized with adjustable 3/8" tension rods. 4/0 upper safety chains provided for additional support. Extensions from 4 to 12 feet.
|
Ceiling Suspended Systems
|
 |
|
The 3100 Series Single Post Backstop offers the designer the most options and versatility when designing an athletic facility for any level of competition. Available in stationary (Models 3111 & 3115), side folding (Model 3109), rear folding (Model 3105) and forward folding (Models 3103 & 3107) configurations. Please CONTACT to discuss your specific application.
Features:
 6 5/8" O.D. (.156" wall thickness) main mast
2 3/8" O.D. heavy gauge diagonal braces to prevent sway
Large diameter post provides greater strength
Precision die-cut horizontal braces allow for full contact welds
Offset hinge keeps center of gravity behind the pivot point
Easy folding
Easy installation and relatively maintenance free operation
Direct Goal Attachment
Transfers stress through the backboard directly to the support structure
Provides unsurpassed stability and rigidity
Adjustability allows for exact plumbing of backboards
Insures the installer always has the proper direct goal attachment
Adjustable Hangers
Approximately 5" of adjustability for easy installation and precise
leveling of the backstop
All welded construction at heights up to 28'
Clamped units can be provided at any height above 28'
CONTACT for information on welded frames above 28'
Backstops conform to the latest regulations for all levels of competition
|
 |
|
The 3200 Series Bent Single Post Backstops provide the same simple and clean appearance as 3100 series backstops with one major difference. The 3200 series is the facility designer's answer to the problem of interference above the backboard location that requires the main mast to be designed with a 30 degree bend from the vertical position.
They have all of the same features as the 3100 series systems plus:
Main mast bent 30 degrees from vertical allowing for unit installation
around obstructions
|
|
|
 |
|
The 2200 and 2600 Dual Post Backstops offer the traditional look preferred by some architects and athletic directors. Ideal for low truss heights. Available in stationary (Models 2211, 2611, 2215 & 2615), rear folding (Models 2205 & 2605) and forward folding (Models 2203, 2603, 2207 & 2607) configurations. Please CONTACT to discuss your specific application.
Features:
Clear view through the playing area when used with glass backboards
4" offset behind the pivot provides easy folding and maximum stability
Offset Adjustable hangers with approximately 5" of adjustability allow
quick and precise leveling during installation
All-welded design offers exceptional rigidity
1/4" x 1" adjustable steel tension straps stabilize design
Welded backstops offer:
Easy installation
Virtually maintenance-free operation
Precision die-cut horizontal braces allow for full contact welds
Series 2200 Dual Post Backstops specifications:
2 3/8" O.D. heavy gauge steel tube vertical members
2 3/8" O.D. tube load bearing horizontal cross pipes
All other horizontal cross pipes are 1 7/8" O.D. tube spaced 36" on
center
Series 2600 Dual Post Backstops specifications:
3 1/2" O.D. heavy gauge steel tube vertical members
All other horizontal cross pipes are 2 3/8" O.D. tube spaced 36" on
center
Optional: Direct goal attachment
Transfers stress through the backboard directly to the support structure providing unsurpassed stability and rigidity. Adjustability allows for exact plumbing of backboards and insures the installer always has the proper direct goal attachment.
|
| |
| | |
|
|
| |
